TOTAL POWER INT. D60 AC-DC 60W POWER SUPPLY WITH DUAL OUTPUT
.LOW COST, HIGH RELIABILITY .105C OUTPUT CAPACITOR .INTERNATIONAL AC INPUT RANGE .COMPACT SIZE, LIGHT WEIGHT .100% FULL LOAD BURN-IN TEST .BUILT IN EMI FILTER, LOW RIPPLE NOISE
.HIGH EFFICIENCY, LOW WORKING TEMPERATURE .SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT .SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED MODEL SPECIFICATION DC OUTPUT VOLTAGE OUTPUT V. TOLERANCE OUTPUT RATED CURRENT OUTPUT CURRENT RANGE RIPPLE & NOISE LINE REGULATION LOAD REGULATION DC OUTPUT POWER EFFICIENCY DC VOLTAGE ADJ. INPUT VOLTAGE RANGE AC CURRENT INRUSH CURRENT LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE PROTECTION OVER TEMP. PROTECTION TEMP. COEFFICIENT SETUP, RISE, HOLD UP TIME VIBRATION WITHSTAND VOLTAGE ISOLATION RESISTANCE WORKING TEMP., HUMIDITY STORAGE TEMP., HUMIDITY DIMENSION WEIGHT SAFETY STANDARDS EMC STANDARDS NOTE : CH1 5V 2% 4A 0.3-6A 75mVp-p 0.5% 0.5% 56W 73% CH1:+10,-5% 85~264VAC 47~63Hz; 120~370VDC 2A/115V 1A/230V COLD START 30A/115V 60A/230V <1mA/240VAC 105%~150% TYPE:PULSING HICCUP SHUTDOWN RESET:AUTO RECOVERY CH1:5.75~6.75V ---------0.03% / C (0~50C) ON +5V OUTPUT 800ms, 50ms, 10ms / 115VAC 300ms, 50ms, 80ms / 230VAC 10~500Hz, 2G 10min./1cycle, PERIOD FOR 60min. EACH AXES I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M Ohms -10C~+60C(REFER TO OUTPUT DERATING CURVE), 20%~90% RH -20C~+85C, 10%~95% RH 159*97*38mm CASE:901 0.55Kgs UL1012, TUV EN60950, IEC950, UL1950 APPROVED CISPR22 (EN55022) CLASS B, IEC801-2,3,4, IEC555-2 VERIFICATION D-60A CH2 12V 6% 3A 0.2-4A 150mVp-p 1% 4% CH1 5V 2% 3A 0.3-6A 75mVp-p 0.5% 0.5% 58W 76% CH1:+10,-5% D-60B CH2 24V 5% 1.8A 0.2-2.2A 150mVp-p 0.5% 4%
1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25C 70% RH. AMBIENT. 2.TOLERANCE GINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION. 3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR. 4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD. 5.LOAD REGULATION IS MEASURED FROM 20% TO 100% RATED LOAD, AND OTHER OUTPUT AT 60% RATED LOAD. 6.EACH OUTPUT PROVIDE UP TO MAXIMUM CURRENT, BUT TOTAL LOAD CAN NOT EXCEED MAX. OUTPUT POWER. 7.C2,3,6 MUST BE REMOVED. 2000-10-03
|
